Skip to main content
WISE COUNTY PSA ENGINEERING RESOURCES
Standard Details
Section 100 Details - General Utility |
||
|
DETAIL 101 - ANCHOR BLOCK
|
||
|
DETAIL 102 - THRUST BLOCK HORIZONTAL BENDS, TEES & DEAD ENDS
|
||
|
DETAIL 103 - THRUST BLOCK VERTICAL BENDS
|
||
|
DETAIL 104 - MECHANICAL JOINT RESTRAINT TABLE FOR PVC PIPES
|
||
|
DETAIL 105 - MECHANICAL JOINT RESTRAINT TABLE FOR DIP PIPES
|
||
|
DETAIL 106 - PIPE BEDDING FOR PRESSURIZED LINES
|
||
|
DETAIL 107 - PIPE BEDDING FOR GRAVITY LINES
|
||
|
DETAIL 108 - CASING PIPE REQUIREMENTS
|
||
|
DETAIL 109 - STEEL CASING FOR CARRIER PIPES
|
||
|
DETAIL 110 - CONCRETE ENCASEMENT
|
||
|
DETAIL 111 - TRACER WIRE INSTALLATION
|
||
Section 200 Details - Water Systems |
||
|
DETAIL 201 - WATER SERVICE - 3/4" LESS THAN 120 PSI
|
||
|
DETAIL 202 - WATER SERVICE - 1" LESS THAN 120 PSI
|
||
|
DETAIL 203 - WATER SERVICE - 1-1/2" & 2" LESS THAN 120 PSI
|
||
|
DETAIL 204 - WATER SERVICE - 3/4"" GREATER THAN 120 PSI
|
||
|
DETAIL 205 - WATER SERVICE - 1" GREATER THAN 120 PSI
|
||
|
DETAIL 206 - WATER SERVICE - 1-1/2" & 2" GREATER THAN 120 PSI
|
||
|
DETAIL 207 - WATER SERVICE PAVEMENT CROSSING
|
||
|
DETAIL 208 - WATER VALVE INSTALLATION
|
||
|
DETAIL 209 - WATER VALVE BOX
|
||
|
DETAIL 210 - COMBINATION AIR RELEASE VACUUM VALVE OFFSET - IN TRAFFIC
|
||
|
DETAIL 211 - COMBINATION AIR RELEASE VACUUM VALVE
|
||
|
DETAIL 212 - BLOW-OFF VALVE ASSEMBLY - OFFSET
|
||
|
DETAIL 213 - BLOW-OFF VALVE ASSEMBLY - IN LINE
|
||
|
DETAIL 214 - FIRE HYDRANT - CURB & GUTTER
|
||
|
DETAIL 215 - FIRE HYDRANT - DITCH & FLAT LAND
|
||
|
DETAIL 216 - WATER MAIN FUTURE EXTENSION
|
||
|
DETAIL 217 - WATERLINE FILL & PROTECTION ASSEMBLY
|
||
Section 300 Details - Wastewater Systems |
||
|
DETAIL 301 - SEWER MANHOLE 48" DIAMETER
|
||
|
DETAIL 302 - SEWER MANHOLE 60" DIAMETER FOR 24" - 42" LINES
|
||
|
DETAIL 303 - SEWER MANHOLE 18" AND DEEPER
|
||
|
DETAIL 304 - MANHOLE ANGLES & CLEARANCES
|
||
|
DETAIL 305 - SEWER DROP MANHOLE
|
||
|
DETAIL 306 - SEWER DOGHOUSE MANHOLE
|
||
|
DETAIL 307 - SEWER MANHOLE STANDARD FRAME AND COVER
|
||
|
DETAIL 308 - SEWER MANHOLE WATERTIGHT FRAME AND COVER
|
||
|
DETAIL 309 - SEWER LATERALS
|
||
|
DETAIL 310 - MULTI-UNIT 6" SEWER SERVICE CONNECTION
|
||
|
DETAIL 311 - PRIVATE GRINDER PUMP LATERAL CONNECTION
|
||
|
DETAIL 312 - SEWER CLEANOUT BOX
|
||
|
DETAIL 313 - FORCEMAIN TERMINATION DROP STACK TYPE
|
||
|
DETAIL 314 - FORCEMAIN TERMINATION STANDARD TYPE
|
||
|
DETAIL 315 - SEWER VALVE BOX INSTALLATION
|
||
|
DETAIL 316 - SEWER VALVE BOX
|
||
|
DETAIL 317 - SEWER MANHOLE VENT
|
||
Section 400 Details - Utility Testing |
||
|
DETAIL 401 - ALLOWABLE LEAKAGE TABLE FOR WATERLINES & SEWER FORCEMAINS
|
||
|
DETAIL 402 - GRAVITY SEWER LINE LOW PRESSURE AIR TEST TABLE
|
||
|
DETAIL 403 - AIR TEST BACK PRESSURE EQUIVALENCY TABLE
|
||
|
DETAIL 404 - MANHOLE VACUUM TESTING
|
||
Standard Technical Specifications
| 01000 | GENERAL REQUIREMENTS |
| 01100 | SUMMARY |
| 01200 | PAYMENT PROCEDURES |
| 01250 | MEASUREMENT & PAYMENT |
| 01300 | PROJECT MEETINGS |
| 01400 | SUBMITTALS |
| 01500 | DELIVERY, STORAGE, & HANDLILNG |
| 01600 | TEMPORARY FACILITIES |
| 01700 | PROJECT CLOSEOUT |
| 02110 | SITE CLEARING |
| 02225 | TRENCHING & BACKFILLING |
| 02665 | WATER DISTRIBUTION SYSTEM |
| 02730 | SANITARY SEWER SYSTEM |
| 03300 | CAST-IN-PLACE CONCRETE |
| 11135 | SUCTION LIFT PUMP |
| 13420 | CONTROLS AND INSTRUMENTATION |
| 16230 | GENERATORS |
| 16285 | TRANSFER SWITCHES |
Inspection Reports
Gravity Sewer Line Low Pressure Air Testing
Lamp and Mandrel Test Data Sheet
Vacuum Testing of New Sanitary Sewer Manholes
